KMF
For Unimog and tractors from 30 kW / 40 hp
Heavy model for tractors up to 150 kW / 200 hp
The humus KMF is the heaviest and most solid model of humus mulchers. Thanks to high-quality components such as branded roller bearings, angular gears and a case made of fine-grained steel, the humus KMF flail mulchers are designed for a long durability and professional use.
Due to the two-sided three-point frame, the use at the front or rear is possible without any effort. The customer has the possibility to customise the humus KMF flail mulcher optimally for himself and his use with the wide variety of accessories and special equipment.
Fig. with special equipment
The KMF rear-mounted for turf care.
Shredding of scrub in fruit-growing.
The KMF in pasture care.
Well proven range of use
- In pasture and land maintenance
- Mulching of roadside vegetation
- In sports facilities and parkways
- In strawberry orchards and forestry
- Mowing of lawns
- For lawn maintenance at airports and on fallows
- Landscape maintenance
- For shredding prunings,scrub and under growth
- Mulching of corn stover
Basic equipment
- Mounting: front and/or rear
- Width of tray of mulch behind the roller
- Gearbox with free wheel
- High-quality bevel gear: Robust, flexible drive over enhanced V-belt on the rotor shaft, automatic V-belt tensioning
- Self-cleaning roller with large storage and floor-friendly guide to the rounded ends and vertical adjustment of the mulcher
- Adjustable cutting height of 3 to 15 cm at the rear roller
- Serrated counter-cutter in the housing to increase the degree of defibration and reduction of the mulch mass
- Two support legs
- Large track roller Ø 244 mm
- Rotor tube diameter 168 mm
Accessories / special equipment
- PTO
- V-Belt protection plate / reinforcement
- Wear plates
- Lighting equipment
- Metal flaps of Hardox® wear plate
- Hydraulic side shift adjustment track front 44cm / rear 42 cm
- Chain screen instead of metal flaps
- Lateral stageless adjustable wheels in stead of roller
- 2 pcs. front wheels
- Hour meter
- Set of skids
- Two-sided three-point frame for front-and rear-mounting
- Additional stone guard (rubber) in front or for rear area
- Gearbox independent of direction of rotation
- Rear mounting, flat drive
- Balancing device:2x chains, 2x springs
- Front mounting with load relieving device on Unimog
technical data
“Y”-type blades: 54 pcs
System flail: 14 pcs
Working width: 1,80 m
Overall width: 1,99 m
Housing height drive side: 905 mm
Housing height offset side: 539 mm
Max. lateral offset from tractor centre to the left: 1,21 m
Power requirement* min. kW/hp: 30/40
Rpm of PTO: 540,750 or 1.000 U/min
Weight**: approx. 675 kg
* The power requirement also depends upon the grass density and grass height
** Weight may differ according to equipment
“Y”-type blades: 60 pcs
System flail: 16 pcs
Working width: 2,00 m
Overall width: 2,19 m
Housing height drive side: 905 mm
Housing height offset side: 539 mm
Max. lateral offset from tractor centre to the left: 1,41 m
Power requirement* min. kW/hp: 30/40
Rpm of PTO: 540,750 or 1.000 U/min
Weight**: approx. 720 kg
* The power requirement also depends upon the grass density and grass height
** Weight may differ according to equipment
“Y”-type blades: 66 pcs
System flail: 16 pcs
Working width: 2,20 m
Overall width: 2,39 m
Housing height drive side: 905 mm
Housing height offset side: 539 mm
Max. lateral offset from tractor centre to the left: 1,52 m
Power requirement* min. kW/hp: 37/50
Rpm of PTO: 540,750 or 1.000 U/min
Weight**: approx. 730 kg
* The power requirement also depends upon the grass density and grass height
** Weight may differ according to equipment
“Y”-type blades: 72 pcs
System flail: 20 pcs
Working width: 2,40 m
Overall width: 2,62 m
Housing height drive side: 905 mm
Housing height offset side: 539 mm
Max. lateral offset from tractor centre to the left: 1,61 m
Power requirement* min. kW/hp: 44/60
Rpm of PTO: 540,750 or 1.000 U/min
Weight**: approx. 830 kg
* The power requirement also depends upon the grass density and grass height
** Weight may differ according to equipment
“Y”-type blades: 72 pcs
System flail: 20 pcs
Working width: 2,60 m
Overall width: 1,82 m
Housing height drive side: 905 mm
Housing height offset side: 539 mm
Max. lateral offset from tractor centre to the left: 1,72 m
Power requirement* min. kW/hp: 44/60
Rpm of PTO: 540,750 or 1.000 U/min
Weight**: approx. 890 kg
* The power requirement also depends upon the grass density and grass height
** Weight may differ according to equipment
“Y”-type blades: 84 pcs
System flail: 24 pcs
Working width: 2,78 m
Overall width: 3,00 m
Housing height drive side: 905 mm
Housing height offset side: 539 mm
Max. lateral offset from tractor centre to the left: 1,71 m
Power requirement* min. kW/hp: 56/75
Rpm of PTO: 540,750 or 1.000 U/min
Weight**: approx.910 kg
* The power requirement also depends upon the grass density and grass height
** Weight may differ according to equipment
“Y“-type blades
System flails…
with fine-cutting blade or claw blade
Universal flail
Click on the picture of the blade for more details
Specialequipment:
Duetothehydraulic cylinder the KMF can be side shifted by 42 cm.
Even spread of the mulched material.
The KMF works smoothly, without clogging and is suitable for mulching large areas.
High-quality V-belt drive, large-sized roller bearing and internal V-belt tensioner.
The mechanic parallelogram sideshift adjustment (upon request hydraulically controlled) and the serial drive shaft drift.
Special equipment: chain screen.
Chain screen instead of metal flaps
Lateral stagelesss adjustable wheels instead of roller
2 pcs. front wheels
Set of skids
Two-sided three-point frame for front-and rear-mounting
Additional stone guard (rubber) in front
Rear mounting, flat drive
Gearbox independent of direction of rotation
Hydraulic side shift adjustment track front 44 cm / rear 42 cm
Balancing device: 2 x chains, 2 x springs, front mounting with load relieving device on Unimog
