PML
For tractors from 110 kW / 150 hp

The new PML humus flail mulcher can be operated in front or rear attachment. Thanks to the new Hardox steel housing, it was possible to achieve a significant weight reduction. Thus the lightweight PML humus flail mulcher is by no means inferior to its big brother, the KMF, in rigidity and stability and offers convincing performance thanks to its lightweight design. For example, with its lowest possible machine weight of 760 kg, working widths of up to 2.78 meters can be achieved. The machine is factory-equipped with skids. The skids stabilise the machine in motion and prevent the rotor shafts from penetrating too deeply into the soil. Thanks to the minimal machine weight, the PML is also suitable for slope tractors. The PML is designed for tractors up to 150 hp.
Fig. with special equipment

Well proven range of use
- In pasture and land maintenance
- Mulching of roadside vegetation
- In strawberry orchards and forestry
- Mowing of lawns
- For lawn maintenance at airports and on fallows
- Landscape maintenance
- For shredding prunings, scrub and undergrowth
- Mulching of corn stover
Basic equipment
- Width of tray of mulch behind the roller
- Gearbox with free wheel
- High-quality bevel gear: Robust, flexible drive over enhanced V-belt on the rotor shaft, automatic
- V-belt tensioning
- Self-cleaning roller with großer Pendelrollenlagerung, Laufwalzendurchmesser 170 mm
- Adjustable cutting height of 3 to 15 cm at the rear roller
- Serrated counter-cutter in the housing to increase the degree of defibration and reduction of the mulch mass
- Two support legs
- Rotor tube diameter 168 mm
- Hardox® wear plate housing
- Housing height drive side 904 mm
- Housing height offset side 538 mm
Accessories / special equipment
- PTO
- Hydraulic side shift adjustment track front 44 cm / rear 42 cm
- Additional rubber stone impact guard in the front area
- Two-sided three-point frame for front / rear mounting
- Additional rubber stone impact guard in the rear area
- Wear plates up to 2.2 m working width
- Wear plates from 2.2 m working width
- Lighting equipment
- Metal flaps of Hardox® wear plate, surcharge up to working width 2,4 m
- Metal flaps of Hardox® wear plate, surcharge up to working width 2,78 m
Technical data
„Y“-type blades: 66 pcs.
System flail: 16 pcs.
Working width: 2.20 m
Overall width: 2.37 m
Max. lateral offset from tractor centre to the left: 1.5 m
Power requirement* min. kW/hp: 37/50
Rpm of PTO: 540, 750 or 1,000 U/min
Weight**: approx. 620 kg
* The power requirement also depends upon the grass density and grass height
** Weight may differ according to equipment
„Y“-type blades: 72 pcs.
System flail: 20 pcs.
Working width: 2.40 m
Overall width: 2.57 m
Max. lateral offset from tractor centre to the left: 1.63 m
Power requirement* min. kW/hp: 44/60
Rpm of PTO: 540, 750 or 1,000 U/min
Weight**: approx. 670 kg
* The power requirement also depends upon the grass density and grass height
** Weight may differ according to equipment
„Y“-type blades: 72 pcs.
System flail: 20 pcs.
Working width: 2.60 m
Overall width: 2.77 m
Max. lateral offset from tractor centre to the left: 1.71 m
Power requirement* min. kW/hp: 44/60
Rpm of PTO: 540, 750 or 1,000 U/min
Weight**: approx. 700 kg
* The power requirement also depends upon the grass density and grass height
** Weight may differ according to equipment
„Y“-type blades: 84 pcs.
System flail: 24 pcs.
Working width: 2.78 m
Overall width: 2.95 m
Max. lateral offset from tractor centre to the left: 1.83 m
Power requirement* min. kW/hp: 56/75
Rpm of PTO: 540, 750 or 1.000 U/min
Weight**: approx. 760 kg
* The power requirement also depends upon the grass density and grass height
** Weight may differ according to equipment

Hydraulic side shift adjustment track front 44 cm / rear 42 cm

Two-sided three-point frame for front / rear mounting

Additional rubber stone impact guard in the front area

Additional rubber stone impact guard in the rear area

Chain screen instead of metal flaps